SKEMA JARINGAN RAPID PVST+ CISCO PACKET TRACER

Per-Vlan Spanning Tree atau PVST merupakan cisco proprietary dimana protocol ini akan memungkinkan untuk menggunakan Spanning Tree Protocol pada per Virtual LAN atau VLAN.
Pada umumnya terdapat dua jenis PVST ialah Per-Vlan Spanning Tree Plus (PVST +) dan Per-Vlan Rapid Spanning Tree (PVRST).

Berikut langkah – langkah konfigurasinya :

konfigurasi switch S1

S1>en
S1#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
S1(config)#vlan 10
S1(config-vlan)#vlan 20
S1(config-vlan)#vlan 30
S1(config-vlan)#vlan 40
S1(config-vlan)#vlan 50
S1(config-vlan)#vlan 60
S1(config-vlan)#vlan 70
S1(config-vlan)#vlan 80
S1(config-vlan)#vlan 99
S1(config-vlan)#int range f0/1-4
S1(config-if-range)#switchport mode trunk
S1(config-if-range)#switchport trunk native vlan 99
S1(config)#int vlan 99
S1(config-if)#ip add 172.17.99.11 255.255.255.0
S1(config-if)#no shut
S1(config)#spanning-tree mode rapid-pvst
S1(config)#spanning-tree vlan 1,10,30,50,70 root primary

konfigurasi switch S2S2(config)#int fa0/11
S2(config-if)#switchport mode access
S2(config-if)#switchport access vlan 10
S2(config-if)#spanning-tree bpduguard enable
S2(config-if)#spanning-tree portfast
S2(config-if)#no shut
S2(config)#int fa0/18
S2(config-if)#switchport mode access
S2(config-if)#switchport access vlan 20
S2(config-if)#spanning-tree bpduguard enable
S2(config-if)#spanning-tree portfast
S2(config-if)#no shut
S2(config)#int fa0/6
S2(config-if)#switchport mode access
S2(config-if)#switchport access vlan 30
S2(config-if)#spanning-tree bpduguard enable
S2(config-if)#spanning-tree portfast
S2(config-if)#no shut
S2(config-if)#vlan 10
S2(config-vlan)#vlan 20
S2(config-vlan)#vlan 30
S2(config-vlan)#vlan 40
S2(config-vlan)#vlan 50
S2(config-vlan)#vlan 60
S2(config-vlan)#vlan 70
S2(config-vlan)#vlan 80
S2(config-vlan)#vlan 99
S2(config-vlan)#ex
S2(config)#int vlan 99
S2(config-if)#ip add 172.17.99.12 255.255.255.0
S2(config-if)#no shut
S2(config-if)#ex
S2(config)#spanning-tree vlan 1,10,20,30,40,50,60,70,80,99 root secondary
S2(config)#spanning-tree mode rapid-pvst

konfigurasi switch S3

S3>en
S3#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
S3(config)#vlan 10
S3(config-vlan)#vlan 20
S3(config-vlan)#vlan 30
S3(config-vlan)#vlan 40
S3(config-vlan)#vlan 50
S3(config-vlan)#vlan 60
S3(config-vlan)#vlan 70
S3(config-vlan)#vlan 80
S3(config-vlan)#vlan 99
S3(config-vlan)#int range f0/1-4
S3(config-if-range)#switchport mode trunk
S3(config-if-range)#switchport trunk native vlan 99
S3(config)#spanning-tree mode rapid-pvst
S3(config)#spanning-tree vlan 20,40,60,80,99 root primary
S3(config)#int vlan 99
S3(config-if)#ip address 172.17.99.13 255.255.255.0
S3(config-if)#no shut

Sumber : https://insidelaptops.wordpress.com/2019/11/04/38/